Difference between revisions of "Scale Communication"
(Created page with "= Cable = = Configuration = = Testing communication =") |
|||
| (32 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | + | [[Category:Tips]] | |
| + | If a serial port scale is used, perhaps the hardest part of this project is getting the scale to talk to the computer. If you are having problems, here are some tips. | ||
| − | + | Talking to the scale is straight forward. Usually send a short character string to the scale and listen for a reply. For the Adam Equipment: | |
| − | = Testing communication = | + | <pre> |
| + | # Set the port to 9600 baud, 8 bit, no parity | ||
| + | stty -F /dev/ttyUSB0 -hupcl ignbrk -icrnl -ixon -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke igncr cs8 -parenb 9600 -parodd | ||
| + | # | ||
| + | # do a quick read to clear any garbage | ||
| + | read -t 0 SCALE < /dev/ttyUSB0 | ||
| + | # | ||
| + | # spawn a process that waits a few milliseconds and then sends the command to the scale | ||
| + | # this gives the read command time to start listening | ||
| + | `sleep 0.01;echo -e -n "N\r\n" > /dev/ttyUSB0` & | ||
| + | # | ||
| + | # read the scale but give it plenty of time to respond | ||
| + | read -t 8 SCALE < /dev/ttyUSB0 | ||
| + | |||
| + | </pre> | ||
| + | |||
| + | |||
| + | == Cable == | ||
| + | ===RS-232 Serial Communication Ports=== | ||
| + | |||
| + | Depending on whether the scale is wired for DTE or DCE, it may require a [http://en.wikipedia.org/wiki/Null_modem null modem] cable or replacing and rewiring the serial connector. | ||
| + | |||
| + | ===RS-232 to USB Adapter=== | ||
| + | If the computer doesn't have a serial port (like the Pi) a USB/RS-232 adapter can be used. They usually map in as /dev/ttyUSB0. | ||
| + | |||
| + | The Prolific chip set has good reviews from the Linux community, but every adapter we've tested has worked fine. Check Amazon | ||
| + | |||
| + | *Prolific PL2303HX Rev D Chipset RS-232 to USB cable Plugable Technologies | ||
| + | |||
| + | ===RS-232 (Null Modem) to USB Adapter=== | ||
| + | This is a little more expensive, but this is a USB/RS-232 adapter with a build in null modem. It should just plug in and work with the Adam CPW200plus. | ||
| + | |||
| + | *StarTech.com 1 Port USB to Null Modem RS232 DB9 Serial DCE Adapter Cable with FTDI, Black (ICUSB232FTN) [http://www.amazon.com/dp/B008634VJY/ref=pe_385040_30332190_TE_M3T1_ST1_dp_1] | ||
| + | |||
| + | == Configuration == | ||
| + | |||
| + | Set up the scale. 9600 baud, 8 bit, no parity | ||
| + | |||
| + | ===Adam Equipment CPWplus200=== | ||
| + | {{:Adam Equipment CPWplus200 Configuration}} | ||
| + | |||
| + | == Testing communication == | ||
| + | |||
| + | A terminal emulation program like Minicom can be used to test the scale communication. | ||
| + | |||
| + | To talk to the scale using a terminal emulation program, configure the software so there is no flow control, either hardware or xon/xoff. | ||
| + | |||
| + | During initial testing, if trouble is encountered communicating with the scale, it may be useful to set the scale in trn 2 mode so that it continuously transmits data. It will serve as a signal generator and the data should continuously scroll across the screen. This does not confirm that you can talk to the scale, only that the cabling is correct. | ||
| + | |||
| + | == Configuring the computer's serial port == | ||
| + | If the computer you are using (laptop or desktop) has a serial port, a USB/Serial adapter is not necessary. The null modem cable can plug into the serial port on the computer. They usually map in like /dev/ttys. | ||
| + | |||
| + | On the linux distributions we've tested, the serial port doesn't need configuration. However, if you have trouble talking to the scale, this is something to try. | ||
| + | |||
| + | To list the line parameters for ttyS0: | ||
| + | stty -F /dev/ttyS0 -a | ||
| + | |||
| + | Example: | ||
| + | <pre> | ||
| + | # stty -F /dev/ttyS0 -a | ||
| + | speed 9600 baud; rows 0; columns 0; line = 0; | ||
| + | intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; eol2 = <undef>; swtch = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W; lnext = ^V; | ||
| + | flush = ^O; min = 1; time = 0; | ||
| + | -parenb -parodd cs8 hupcl -cstopb cread clocal -crtscts | ||
| + | -ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl ixon -ixoff -iuclc -ixany -imaxbel -iutf8 | ||
| + | opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0 | ||
| + | isig icanon iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt echoctl echoke | ||
| + | </pre> | ||
| + | |||
| + | |||
| + | stty can also be used to set the serial port parameters. If it almost works (ie getting data from the scale but maybe with some garbage characters), try setting the serial port parameters: | ||
| + | |||
| + | <pre> | ||
| + | stty -F/dev/ttyS0 -hupcl ignbrk -icrnl -ixon -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke igncr | ||
| + | </pre> | ||
Latest revision as of 18:21, 22 February 2015
If a serial port scale is used, perhaps the hardest part of this project is getting the scale to talk to the computer. If you are having problems, here are some tips.
Talking to the scale is straight forward. Usually send a short character string to the scale and listen for a reply. For the Adam Equipment:
# Set the port to 9600 baud, 8 bit, no parity stty -F /dev/ttyUSB0 -hupcl ignbrk -icrnl -ixon -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke igncr cs8 -parenb 9600 -parodd # # do a quick read to clear any garbage read -t 0 SCALE < /dev/ttyUSB0 # # spawn a process that waits a few milliseconds and then sends the command to the scale # this gives the read command time to start listening `sleep 0.01;echo -e -n "N\r\n" > /dev/ttyUSB0` & # # read the scale but give it plenty of time to respond read -t 8 SCALE < /dev/ttyUSB0
Contents
Cable
RS-232 Serial Communication Ports
Depending on whether the scale is wired for DTE or DCE, it may require a null modem cable or replacing and rewiring the serial connector.
RS-232 to USB Adapter
If the computer doesn't have a serial port (like the Pi) a USB/RS-232 adapter can be used. They usually map in as /dev/ttyUSB0.
The Prolific chip set has good reviews from the Linux community, but every adapter we've tested has worked fine. Check Amazon
- Prolific PL2303HX Rev D Chipset RS-232 to USB cable Plugable Technologies
RS-232 (Null Modem) to USB Adapter
This is a little more expensive, but this is a USB/RS-232 adapter with a build in null modem. It should just plug in and work with the Adam CPW200plus.
- StarTech.com 1 Port USB to Null Modem RS232 DB9 Serial DCE Adapter Cable with FTDI, Black (ICUSB232FTN) [1]
Configuration
Set up the scale. 9600 baud, 8 bit, no parity
Adam Equipment CPWplus200
See Section Section 13 of the CPW200plus User Manual for detailed instructions.
With the scale off, hold the Tare/Zero button and press the On/Off button.
| Parameter | Setting | Rational |
|---|---|---|
| Auto Power Off | Pr oFF | Don't want the scale to turn off after a period of inactivity. |
| Backlight always off | bL 1 | Increases battery life when AC power fails. |
| Baudrate | 9600 | Default |
| 8 Bit no parity | PAr 1 | Default |
| Transmission Mode | trn 1 | Default. Can set to trn 2 during trouble shooting. |
Testing communication
A terminal emulation program like Minicom can be used to test the scale communication.
To talk to the scale using a terminal emulation program, configure the software so there is no flow control, either hardware or xon/xoff.
During initial testing, if trouble is encountered communicating with the scale, it may be useful to set the scale in trn 2 mode so that it continuously transmits data. It will serve as a signal generator and the data should continuously scroll across the screen. This does not confirm that you can talk to the scale, only that the cabling is correct.
Configuring the computer's serial port
If the computer you are using (laptop or desktop) has a serial port, a USB/Serial adapter is not necessary. The null modem cable can plug into the serial port on the computer. They usually map in like /dev/ttys.
On the linux distributions we've tested, the serial port doesn't need configuration. However, if you have trouble talking to the scale, this is something to try.
To list the line parameters for ttyS0: stty -F /dev/ttyS0 -a
Example:
# stty -F /dev/ttyS0 -a speed 9600 baud; rows 0; columns 0; line = 0; intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; eol2 = <undef>; swtch = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 0; -parenb -parodd cs8 hupcl -cstopb cread clocal -crtscts -ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl ixon -ixoff -iuclc -ixany -imaxbel -iutf8 opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0 isig icanon iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt echoctl echoke
stty can also be used to set the serial port parameters. If it almost works (ie getting data from the scale but maybe with some garbage characters), try setting the serial port parameters:
stty -F/dev/ttyS0 -hupcl ignbrk -icrnl -ixon -opost -onlcr -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke igncr
